To buy a used car, be sure to do your homework in advance. The trade fair provided vehicle certification, eliminating vehicles with problems with accidents and procedures. However, when owners are widely viewing their used cars on weekdays, they still need to beware of the three major consumption traps that are common when used cars are purchased. Knowing yourself and knowing oneself can not fall into the trap. Xiaobian arranges as follows, hoping to help you buy a good car.  

1、Accident car posing as a good car  

Buying an accident car posing as a good car is a problem that second-hand car buyers are most worried about. Vehicles that have undergone a serious accident have been severely deformed in the body or chassis. Even if they are restored through maintenance, the vehicle's sealing, sound insulation, and safety are not as good as before; if the engine is overhauled or the vehicle is seriously damaged, the power is There is also a big hidden danger in handling and control, and there is a huge difference between the value and the normal used car.  

solution:  

Look at the paint: The most intuitive part of the car paint, the general factory spray paint texture (thickness error is less than 1 mm) and the color coordination, and after a lot of collisions will be traced after repainting in many places, paint color or thickness and the surrounding not In line with the sun, it is more obvious. Focus on the door closing point, because the whole car spray paint will not be meticulous to this place, where it is possible to see the original paint color.  

Look at the welding point: see if the internal link of the engine is welded. The original car will be relatively flat, basically do not see any welding traces of parts and components. If there are excessive collisions, this part of the maintenance trace will be more obvious. In addition, the door is close to the top part of the rubber seal, the original vehicle has evenly protruding welding points, and the accident vehicle, especially the front-end or rear side of the vehicle, in the rear door near the roof position about two points One of them will leave marks when cutting and repairing. Open the mat inside the trunk, if there is any maintenance work will see more obvious signs; or look at the arc at the closure of the trunk gap, the general manual operation is difficult to maintain the streamline of the original body.  

For the first-time car buyers, it is also not a matter of nitpicking, simple scraping scratch repair does not harm the body, chassis and engine assembly, etc., do not have to be seen as an accident car.  

2. The mileage of the odometer is reduced  

Adjusting the odometer is a common method used by many second-hand car dealers, and it is technically very easy to operate. The main purpose of adjusting the number of kilometers is to mask the true degree of wear of the vehicle. Such a car usually has many parts to be replaced, and the maintenance cost after purchase is very high.  

solution:  

The number of kilometers used car odometer can not be completely trusted, look at the degree of wear of plastic parts in the car, if the wear is very high, and the number of kilometers is obviously inconsistent, the possibility of adjusting the table is very great. Some components such as wheels, etc., were soaked with chemicals, and the degree of cleanliness was as good as that of new cars. If these parts of a used car are newer than new ones, it is mostly to hide their high-wearing conditions. In addition, if a senior car has a very low mileage, you must beware of it.  

Not only look at the car, but also take a closer look at the "registration certificate", especially focusing on the transfer of the vehicle. Some vehicles have already changed hands several times, and the maintenance and repair status is complex. The depreciation rate of vehicles is greater. Such vehicles must be bought with caution.  

3, vehicle identity is not "aesthetic"  

The condition of the vehicle is almost the same. The value of the car is also very good. At this time, it cannot be careless, and there is still the possibility of “deliberately losing Jingzhou”. The identity of the vehicle, such as smuggling, refitting, mortgage, etc., must be “verified”.  

solution:  

It is unreasonable to consider the various conditions that may occur before the transaction. In addition, it is advisable to pay the deposit first when looking at the car, and then pay the full amount after completing the transfer procedure. This can avoid a lot of unnecessary troubles. In addition, the vehicle actually has its own ID card number, that is, the 17-digit VIN code of the vehicle. It contains the vehicle manufacturer, year, vehicle model, body type and code, engine code and assembly site, etc. information. It is reflected on the body, usually on the underside of the left windshield, vehicle nameplates, hubs, and other locations. For different vehicles, look at the vin code everywhere on the vehicle body. If there are differences, then the vehicle must undergo major changes. At the same time, by reading the VIN code, it is possible to find out important information such as the place of production of the vehicle and the year of production. It is a quick and accurate way to see whether the information and the relevant procedure of the vehicle are consistent.

Computer Control Electronic Universal Testing Machine is designed and manufactured according to ASTM, ISO,DIN etc standards. It is computer-controlled precision Testing Machine, suitable for wide range of material for tension compression, bending and shearing test. It has high stability as well as high precision, equipped with PC system& printer for graph, test result display, test control as set program, printing & data processing. Complete with modulus for metal, spring, textile, rubber, plastic and other material testing & creep test. It is widely used in many field used in many fields such as industry factories, mineral enterprise and high schools. 

Electronic Universal Testing Machine

Utm Machine,Electronic Universal Testing Machine,Laboratory Equipment,Electronic Testing Machine

Jinan Chenda Testing Machine Manufacturing Co., Ltd. , https://www.jncdtester.com

Posted on