Dust Collector Fittings Dust Collector Fittings Dust Collector Fittings,Pulse Solenoid Valves,Star Dischargers,Wind Blockage Vales Botou Youjian Environmental Protection Equipment Co. LTD. , http://www.btdustmachine.com
The Dust Collector accessories include bag bag, skeleton (bag cage), electromagnetic pulse valve, pulse control instrument, star type ash relief valve, and other special accessories for Electrostatic Precipitator, such as anode plate, awn wire, Yin Yang pole vibrator, porcelain bottle, porcelain shaft and so on. It is suitable for accessories such as Bag Filter , Cyclone Dust Collector, wet dust collector, water film dust collector, electrostatic precipitator and other environmental protection dust removal equipment.
Summary
The dust collector is a kind of dust removal equipment, which is designed for the high humidity, low dew point and high dust concentration by using the integrated mechanism of the principle of inertia collision and the combination of electrostatic adsorption.
Principle of composition
Dust catcher accessories include dust bag, skeleton, electromagnetic pulse valve, pulse controller and other special accessories for dust catcher. The filtered flue gas must meet the national emission standard according to the design requirements of the dust collector; the operating resistance of the dust collector is generally kept below 150Pa; the working life of the filter material has reached more than 2 years, and the working life of the solenoid pulse valve of the dust cleaning system has reached 5 years and 100 thousand times.
Product features
The dust collector adopts the principle of combining the inertial separation and filter dust removal. It can handle the high concentration of the mixed air flow and can effectively separate the fine powder below 5um. It is an ideal substitute for the traditional cyclone separator. The dust collector parts should fully understand the features of the dust collector before use, so we need to be treated carefully. Now.
1. the operation is reliable and stable. The noise is low. The fault is small. The service life is long. The gear parts are made of ductile iron and bearing steel.
2. bearing. Gear box. Away from the valve body. Avoid the influence of high temperature dust. The front and rear covers are well sealed to prevent dust leakage and prolong the service life of the moving parts.
3., it has strong overload capacity, low impact torque and is suitable for frequent starting and reverse rotation.
4. by adopting the principle of planetary rotation, the input and output are on the same axis, and have the uniqueness of the direct connection with the motor, so the compact structure is beautiful and novel, small in volume and light in weight.
The elevator is a complex closed environment, and the mature radio monitoring has become the first choice for elevator monitoring applications. The wireless bridge is a transmission device in wireless monitoring, which is convenient to install and low in cost. However, in the actual elevator monitoring and installation process, there will be many problems, here are a few points, I hope to help everyone in the actual installation.
Pit 1: Blind entry?
The elevator belongs to special equipment and has certain dangers. Do not enter the scene blindly.
1. Before installation, we need to go to the property to understand the wiring of on-site elevators, monitoring, etc.
2. First contact the elevator maintenance personnel, the external personnel must be led by the elevator maintenance personnel to enter the field (the elevator operators are required to hold the special operation operation certificate issued by the State Administration of Work Safety to be employed).
Pit 2: How to solve the power supply of the bridge?
The elevator brands are different and the structure is different. The configuration of the top and bottom of the car is different. The power supply of the elevator car roof of the renovation project is very likely to be occupied by the camera. Where does the bridge take power?
During the survey, pay attention to whether the top of the car is a plug. If there is no plug, you need to install a plug to facilitate power.
Pit 3: Where is the bridge installed?
Select the bridge installation point to avoid avoiding obstructions, especially metal substances will affect the signal. The bridge at the top of the elevator car can be installed on the top railing; the other one is installed in the foundation pit?
It is possible that the foundation pit will accumulate water and affect the bridge signal transmission, so it is the most ideal method to fix it on the wall of the elevator shaft.
Pit 4: What is the bridge fixed?
How to fix the bridge at the top or bottom of the elevator shaft?
When the bridge is shipped from the factory, most of the manufacturer's accessories only contain hoops or straps. There is no bracket, so don't forget to buy brackets! Hold the bridge and tie the bridge tightly.
Pit 5: How to set up the bridge?
Most bridge configuration methods on the market:
· WEB interface configuration: first enter the two bridge WEB interface to set the IP address, then set the transmitter, receiver, and finally set the channel.
· Dial-up bridge: The dial-up button on the bridge, some represent the working mode code, packet pairing code, IP address code, this must be carried out with the instructions to study well to complete the pairing well.
Digital display bridge: The set information is visually presented on the bridge, but it still needs to manually set the IP address and channel on the bridge, and then press the bridge's dial button to make it pair successfully. (Original title: Fine pit elevator monitoring bridge installation needs to avoid pits)